The evolution of cutting forces during slot milling of unidirectional carbon fiber reinforced polymer (UD-CFRP) composites

Cutting forces generated during traditional machining of fiber reinforced polymer composites play an important role in determining machined surface quality. The cutting force signals also provide a live indicator of the dynamic behavior of the chip formation process. Cutting forces in machining FRPs are dependent primarily on the instantaneous fiber cutting angle, chip thickness, cutting edge geometry and the current state of cutting edge wear. In this study, effects of the cutting edge rake angle and tool wear on cutting force evolution during slot milling of unidirectional carbon fiber reinforced polymer (UD-CFRP) composite was investigated. The cutting forces were measured in the feed and normal directions and then transformed to the tangential and radial directions of the tool path. A simplified cutting force model consisting of a shearing region and a pressing was used to determine the shearing and friction force components. This allowed determination of the friction coefficient on the clearance face of the tool. It was found that the friction coefficient varied significantly with rake angle and fiber cutting angle. The effect of rake angle on cutting forces is more discernable in the shearing region with positive rake angle tool providing the most efficient cutting. Furthermore, correlations were found between machining damage and the magnitude and orientation of the resultant shearing force

Expected performance of the CDF plug upgrade calorimeter at TeV33

We have evaluated the performance of the CDF plug tile/fiber calorimeter under the radiation environment at a luminosity of 1 x 10{sup 33}cm{sup -2}s{sup -1} at TeV33. The issues covered are the radiation damage, the anode current of photomultipliers, and the energy miss-measurement due to the minimum bias event pile-ups. The plug calorimeter is expected to perform as precision calorimetry in the pseudorapidity range up to {approximately}2.3

Epifluorescent microscopy of edge-trimmed carbon fibre-reinforced polymers : an alternative to computed tomography scanning

X-Ray computed tomography (XCT) can be used to detect edge-milled carbon fibre-reinforced polymer (CFRP) defects. Significantly this method is able to show subsurface defects that cannot be captured by traditional methods such as stylus-based or more novel areal methods of surface quality measurement. While useful, this method can be prohibitive due to high equipment cost, scanning time and image resolution. XCT can often produce artefacts which falsely predict damage or obscure damage and depending on machine X-ray power often cannot resolve damage to fibre diameter which is critical when observing milled quality of the surface/subsurface. This study utilises epifluorescent (EF) optical microscopy to provide high-quality optical images as an alternative to XCT to observe through-depth damage of CFRP materials. The method of computing the novel damage criteria is presented, as well as the validation of the method which compares EF to XCT. Subsurface damage of fabric and unidirectional (UD) materials in 0°, 45°, 90° and −45° orientations to the cutting edge is observed to demonstrate typical defects. A novel metric resulting from the EF method provides a total area of damage when compared to a theoretically straight cut across the face of the edge-milled CFRP. The method shows that different subsurface damage exists for different fibre orientations to the cutting edge, highlighting the clear need for through-depth analysis of machined edges. In addition, the method is shown to be a suitable alternative to XCT with scope for further development of industrial aerospace and automotive quality control of machined CFRP parts

Varying CFRP workpiece temperature during slotting : effects on surface metrics, cutting forces and chip geometry

Carbon fibre reinforced thermoset polymer (CFRP) components are typically edge trimmed using a milling process to achieve final part shape. During this process the material is subject to significant heating at the tool-workpiece interface. Damage due to heating is fibre orientation specific; for some orientations it can lead to matrix smearing, potentially hiding defects and for others it can increase pullout. Understanding these relationships is critical to attaining higher throughput by edge milling. For the first time this study focuses on active heating of the CFRP rather than passive measurement, through use of a thermocouple controlled system to heat a CFRP workpiece material from room temperature (RT) up to 110 °C prior to machining. Differences in cutting mechanisms for fibres oriented at 0, 45, 90 and -45° are observed with scanning electron microscopy (SEM), and quantified with using focus variation with an increase of 89.9% Sa reported between RT and 110°C CFRP panel pre-heating. Relationships to cutting forces through dynamometer readings and tool temperature through infra-red (IR) measurements are also made with a novel optical method to measure cut chips presented. Results show an increase in chip length and width for increasing cutting temperature from RT to 110°C (3.39 and 0.79 µm for length and width, respectively). This work improves current understandings of how the cutting mechanism changes with increased temperature and suggests how improved milling throughput can be achieved

Effects of Kynurenine Pathway Inhibition on NAD+ Metabolism and Cell Viability in Human Primary Astrocytes and Neurons

The kynurenine pathway (KP) is the principle route of L-Tryptophan (TRP) metabolism, producing several neurotoxic and neuroprotective metabolic precursors before complete oxidation to the essential pyridine nucleotide nicotinamide adenine dinucleotide (NAD+). KP inhibition may prove therapeutic in central nervous system (CNS) inflammation by reducing the production of excitotoxins such as quinolinic acid (QUIN). However, KP metabolism may also be cytoprotective through the de novo synthesis of intracellular NAD+. We tested the hypothesis that the KP is directly involved in the maintenance of intracellular NAD+ levels and SIRT1 function in primary astrocytes and neurons through regulation of NAD+ synthesis. Competitive inhibition of indoleamine 2,3 dioxygenase (IDO), and quinolinic acid phosphoribosyltransferase (QPRT) activities with 1-methyl-L-Tryptophan (1-MT), and phthalic acid (PA) respectively, resulted in a dose-dependent decrease in intracellular NAD+ levels and sirtuin deacetylase-1 (SIRT1) activity, and correlated directly with reduced cell viability. These results support the hypothesis that the primary role of KP activation during neuroinflammation is to maintain NAD+ levels through de novo synthesis from TRP. Inhibition of KP metabolism under these conditions can compromise cell viability, NAD-dependent SIRT1 activity and CNS function, unless alternative precursors for NAD+ synthesis are made available

Microbial Community Composition of Two Environmentally Conserved Estuaries in the Midorikawa River and Shirakawa River

To provide a general overview of the microbial communities in environmentally conserved estuaries, the top 5 cm of sediment was sampled from the sandy estuary of the Shirakawa River and from the muddy estuary of the Midorikawa River. Higher amounts of organic matter were detected in the Midorikawa estuary sample than in the Shirakawa estuary sample. Measurement of redox potential revealed that the Shirakawa estuary was aerobic and the Midorikawa estuary was much less aerobic. Clone analysis was performed by targeting partial 16S rRNA gene sequences and using extracted DNA from the samples as a template. Various bacteria were detected, among which Gammaproteobacteria was dominant at both estuaries. Unclassified clones were detected in the Gammaproteobacteria group, mainly among samples from the Midorikawa estuary. Other detected bacterial groups were Alphaproteobacteria, Deltaproteobacteria, Chloroflexi, Actinobacteria, and Bacteroidetes. All the Deltaproteobacteria clones were anaerobic sulfate-reducing bacteria. Those aerobic and anaerobic bacteria coexisted in the top 5 cm of the estuary sediments indicating the surface layer have active sulfur and carbon cycle. Abundance of aerobic Gammaproteobacteria may be an indicator for conserved estuaries

Effects of tool coating and tool wear on the surface quality and flexural strength of slotted CFRP

Machining of carbon fibre reinforced polymer (CFRP) is abrasive and causes significant tool wear. The effect of tool wear on static flexural strength is investigated, using edge trimming with uncoated carbide and chemical vapour deposition (CVD) diamond coated burr style tools. Edge rounding (ER) criteria along with flank wear are used to observe tool degradation with ER shown to preferentially wear allowing the tool to become cyclically sharper and duller, corresponding to fluctuating dynamometer readings, a novelty for CFRP machining. Areal surface metrics degraded for an uncoated tool due to changes in cutting mechanism, whilst for up to 16.2 m of linear traverse, the coated tool showed limited changes. Tool wear, caused by edge trimming 7.2 m of CFRP, using an uncoated carbide tool, provided a flexural strength reduction of up to 10.5 %, directly linking tool wear to reduced mechanical strength

Indoleamine 2,3-dioxygenase is a novel prognostic indicator for endometrial cancer

Indoleamine 2,3-dioxygenase (IDO) is a tryptophan-catabolising enzyme inducing immune tolerance. The present study aimed to investigate IDO expression and its prognostic significance in endometrial cancer. Indoleamine 2,3-dioxygenase expression in endometrial cancer tissues (n=80) was immunohistochemically scored as four groups (IDO−, 1+, 2+, and 3+). The high IDO expression (IDO2+ or 3+) in tumour cells was found in 37 (46.3%) of the 80 cases, and was positively correlated with surgical stage, myometrial invasion, lymph-vascular space involvement, and lymph node metastasis, but not with the histological grade. Patients with high IDO expression had significantly impaired overall survival and progression-free survival (PFS) (P=0.002 and P=0.001, respectively) compared to patients with no or weak expression of IDO (IDO− or 1+). The 5-year PFS for IDO−/1+, 2+, and 3+ were 97.7, 72.9, and 36.4%, respectively. Even in patients with early-stage disease (International Federation of Gynecology and Obstetrics I/II, n=64), the PFS for IDO2+/3+ was significantly poor (P=0.001) compared to that for IDO−/1+. On multivariate analysis, IDO expression was an independent prognostic factor for PFS (P=0.020). These results indicated that the high IDO expression was involved in the progression of endometrial cancer and correlated with the impaired clinical outcome, suggesting that IDO is a novel and reliable prognostic indicator for endometrial cancer

Brevianes Revisited

Breviones are a new family of secondary metabolites that were originally isolated from the New Zealand endemic fungus Penicillium brevicompactum var. Dierckx. These compounds are generally characterized by a new carbon skeleton, known as breviane, which that has three possible structural variations, such as breviane, abeo-breviane, and abeo-norbreviane. Brevianes present a basic diterpenic tricyclic core that is mevalonic in origin and is similar to that of perhydrophenanthrene. The core bears four methyl groups at positions C4, C8, C10, and C13 and has defined stereochemistry at positions C5, C8, C9, C10, and C14. The C1'-C7' side chain has been proposed to have a polyketide biosynthetic origin and is joined to the diterpenic moiety through carbons C2'-C15'. The cyclization and lactonization of this part of the molecule leads to the characteristic breviane spiranic ring fused to the α-pyrone

Origin of Low-Frequency Negative Transconductance Dispersion in p-HEMT

Measurements of low-frequency transconductance dispersion at different temperatures and conductance deep level transient spectroscopic(CDLTS) studies of an AlGaAs/InGaAs pseudomorphic HEMT were carried out. The experimental results show the presence of defect states at the AlGaAs/InGaAs hetero-interface. A mobility degradation model was developed to explain the low frequency negative transconductance dispersion as well as the apparent hole-like peaks observed in the CDLTS spectra. This model incorporates a time dependent change in 2DEG mobility due to ionised impurity scattering by the remaining charge states at the adjoining AlGaAs/InGaAs hetero-interface